|
|
|
|
| The new generation of Digital Switch Mode Power Supplies FAC
series QP23, has been designed and manufactured to assist and give solutions to the DC voltage
control and power needs raised in very diverse applications.The FAC series QP23 contributes to the ideal solution for the AC to
DC voltage transformation needs, by means of a filter, a rectifier and a control process with the end result of an optimal voltage,
in accordance to the particular needs of each application.The paralleling feature of the series, and its capacity to store
energy through the batteries with a high autonomy capability, turns the FAC series QP23 into a range of products highly adequate for
different applications for top technology. |
 |
| The FAC series QP23 has been designed to meet the highest level of specification, where utmost reliability,
safety and efficiency is required.This equipment offers many advantages and benefits in a wide range of applications where AC mains supply needs to be converted
to DC voltage.
|
| |
 |
|
|
|
|
|
|
|
| 50 The setting up of a new module in parallel, does not
require any additional element.
Should you want to have an exhaustive control of the
rectifier’s assembly or even of the room where the
supply or associated elements are installed, as an
option, it is possible to set up a centralised intelligent
control module.
The setting up of the MS-101 Centralised intelligent
Control System enables controlling of all the connected
modules and the communication with a personal
computer via serial interface, which, with the proper
software, allows to control, to acknowledge alarms,
to program and to control the system as a sole and
intelligent set.
|
The MS-101 control system permits to carry out the
following measurements and alarm controls:
Input measurements
• Input voltage 1: Phase to phase and phase to
neutral.
• Input voltage 2: Phase to phase.
• Current.
• Apparent power (VA) : By phase and total.
• Actual power (W): By phase and total.
• Power factor.
• Low output voltage.
• High output current.
• High battery temperature.
• High FAC cabinet temperature.
The alarms of the mentioned MS-101 module can
be configured by the user according to the needs of
|
|
|
 |
| |
|
|
|
| Power factor
|
1
|
Voltage
|
12,24,48,60,110,125,220,DCV.
|
| Nominal Current
|
Depending on model
|
Accuracy
|
+/- 0.1% (with charged batteries).
|
| Efficiency
|
>90%
|
Ripple level
|
< 20 mVpp
|
| Frequency
|
50 / 60 Hz
|
Rated Level
|
Depending on the model
|
| Protection
|
By fuses
|
Nominal Current
|
Depending on the model
|
|
|
|
Autonomy (if needed)
|
To be determined
|
|
|
|
| Single and three phase
|
SMPS* (PWM) with PFC*
|
Type
|
Lead-acid, maintenance free Ni-Cad (optional).
|
| Protections
|
Against 5 kV peaks. (8/20 µs pulses)
|
Type of charge
|
>I/U constant
|
|
|
|
Charge current
|
0,1 C. (adjustable)
|
|
|
|
Time to recharge
|
Up to 80% in 4 hours.
|
|
|
|
Protections
|
Over-under voltages
|
|
|
|
| Dieletic Strength
|
3.000 ACV 1 min
|
LCD display
|
Output voltage, output current, output
power, battery charge current, temperatures,
alarms and calibrations
|
| Protection level according to
UNE 20 324 78 IR Standard
|
IP 20
|
Visual
|
Discharge, float, alarm, ON/OFF
|
| Insulation
|
> 10 M˝
|
Relay Interface
|
Rectifier’s failure, line present,discharge, end of autonomy alarm,minimal utilisation voltage
|
| Audiable noise at 1m
|
<40 dB
|
Optocouplings
|
Shutdown
|
| Ventalation
|
Natural
|
Serial port
|
RS-485 or RS-232C.
*SMPS (switch mode power supply)
*PFC (power factor correction)
|
| Operating tempreture
|
0 to + 40°C
|
|
|
| Storage tempreture
|
- 20 to + 40°C
|
|
|
| Relative humidity
|
Up to 95% non condensing
|
|
|
| Max. working altitude
|
Sea level to 2.400 m.
|
|
|
| MTBF
|
60.000 hours.
|
|
|
| MTTR
|
30 min
|
|
|
| Compliance to standards
|
EN 61204 (1995).
IEC 1204-3 (Future EN 61204-3).
EN 41003.
|
|
|
|
|
